Showing all 71 results
Snowmobile specific grip glue. Will not break down in snowmobile grip heater scenario
Allows for Quick and Easy Adapting for Oversize Handlebars
• One piece 5″ rubber grip.
• Ultra tacky diamond grip surface is soft and comfortable.
• Compatible with hand warmers.
• Sold per pair.
• One piece 8″ rubber grip.
• Ultra tacky diamond grip surface is soft and comfortable.
• Compatible with hand warmers.
• Sold per pair.
Great and simple Way to add Protection on your Stock Polaris Handlebars or Personalize your RSI Aluminum rise Handlebars
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
BILLET ALUMINUM ENGINE KILL SWITCH PUSH BUTTON BLACK
CHROMOLY 13 DEGREE HANDLEBAR
CHROMOLY 16 DEGREE HOOKED HANDLEBAR
CHROMOLY HUSTLER HANDLEBAR 1″ RISE HOOKED HANDLEBARS
Accepts 7/8″ and oversize 1 & 1/8″ Handlebars. Universal Installation on any t-post steering post.
Replacement LH Side Spring style Scratcher
Univeral replacement tether cord.
Flexible LED Lighted Handgurads will not break in the event of a roll over.
Universal Heater kit- requires 12 volt power source.
• Dual pivoting adjustability allows you to position handlebars where you want them.
• The shortest pivoting Riser available on the market at 1″
• Easy one bolt installation is super easy and very strong.
• Accepts both Standard 7/8″ and 1 & 1/8″ Oversized Handlebars
Extended style heater element 2 Wire Grip heaters OEM terminals plug and play installation
Standard 2 Wire Grip heaters OEM terminals plug and play installation
Billet Throttle block uses OEM Kill Switch
Billet Throttle block With Plug and Play Billet Kill Switch
Billet Throttle block With Universal Billet Kill Switch
Replacement LH Side Spring style Scratcher
Replacement RH Side Spring Style Scratcher
Small Diameter grip with Tons of Grip
STANDARD PLASTIC MOMETARY PUSH BUTTON
Bolt on intstallation allowing Rider to position Hook orientation
Add handlebar hooks to your favorite handlebars
**Sold individually to put hooks on both ends of your handlebars order qty 2**
Kit includes Grips and hooks to transform any RSI aluminum Handlebar
UNIVERSAL BILLET ALUMINUM ELECTRONIC REVERSE PUSH BUTTON BLACK (EXCEPT ELECTRIC START )
Standard Square heater element grip heaters
Normally Closed tether cord
Normally open tether cord
Universl Grip insulator, thin profile, synthetic based insulator install in seconds.
*Required for all machines using grip heaters*
Lightweight Wire type Scratcher. Universal installation
Fully CNC Billet Brake Lever powder coated black €œShorty style€ Two finger operation
Uses OEM mounting hardware.
Fully CNC Billet Brake Lever €œShorty style€ Two finger operation
Uses OEM mounting hardware.
2008-20 Ski-Doo QRS Jackshaft Alignment Shim Kit Includes 4 Clutch Side Bearing Shims, 3 Bearing retainer Shims, 1 Beveled Gear side Retainer Shim, 3 Gear side Bearing shims
Quick adjust, just as the name says not tools required for your trailside clicker changes
TRA Primary clutch holder for installation and removal of the TRA primary clutch.
Quickest and easiest Solution for a leaky, and hard to remove oil cap
Universal installation Reversible ice scratcher, replaceable carbide tip good for years of constand use.
Carbide tip is a wear item and may break do to hitting objects on the trails. This is to protect not having any issues with hanging up on the rail.
12″ Designed to be mounted on the suspension rail
Replacement bit for 151-106
Tungsten inserts for TRA Adjustable pin kits
Slim profile Ratcheting Torx bit. Allows for removal of helix bolts while keeping the QRS Secondary clutch on the sled.
Remove helix or change secondary rollers all without removing the Jackshaft or touching the Chaincase.
Ski-Doo Secondary Spring Fits all RER Clutches HPV, LPV & QRS
TRA Heavy Pin Kit 16-27g Includes Tungsten Slugs
TRA Light Pin Kit 11.1-16.0g
TRA Medium Full Range Pin Kit 13-23.1g Includes Tungsten Slugs
Compleytly adjustable TRA arms Fits all TRA 3, TRA 5 and TRA 7
SPD31 Ramps Fits all TRA 3, TRA 5 and TRA 7
Universal compressor works on most primary and secondary clutches (does not work on P-Drive Primary clutch or QRS Secondary)
Complete adjustable weight kit or Fine Tuning kit
QRS smooth Shift Bearing (works on all 2008 Ski-doo QRS secondary machines) 2012-18 Arcitic Cat Secondary, 2018-21 Arcitc Cat with boss secondary
TRA Primary clutch puller for removal of the TRA primary clutch. (works on all TRA’s except 583 and 617 engines)
3 Piece Button holder to keep buttons in place for assembly/ disassembly.
2.5lb Nitrous Bottle (non-siphon tube)
2.5lb Nitrous Bottle with Siphon Tube