Latest Products
-
Hustler Aluminum 7/8″ CLAMP AREA – 7/8″ HOOKED HANDLEBAR - 13 DEGREE SWEEP – 1″ RISE – 30″ WIDE – 1″ RISE - Hydro Dipped Carbon Fiber
$ 149.95
-
POLARIS 650/850/900R/BOOST TETHER MOUNT FOR RMK STEERING STEM
$ 19.95
-
Ski-Doo QRS Secondary Spring - Torsional Black
$ 25.00
-
ARCTIC CAT CATALYST CHASSIS BILLET ALUMINUM MOMENTARY KILL SWITCH BLACK ANODIZED W/ OEM CONNECTOR
$ 59.95
-
Ski-doo Rev Gen 4/ NEO Performance Trail Kit (includes adjustable P-drive weights) 6000+ Clutch Kit for Straightline Exhaust (40 and 55hp Engine Package)
$ 449.95
-
Snowmobile specific grip glue. Will not break down in snowmobile grip heater scenario
-
• One piece 5″ rubber grip.
• Ultra tacky diamond grip surface is soft and comfortable.
• Compatible with hand warmers.
• Sold per pair.
-
• One piece 8″ rubber grip.
• Ultra tacky diamond grip surface is soft and comfortable.
• Compatible with hand warmers.
• Sold per pair.
-
Bolt on intstallation allowing Rider to position Hook orientation
-
Kit includes Grips and hooks to transform any RSI aluminum Handlebar
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
- Self adhesive grip tape to fully wrap your handlebars and hooks with a seamless finish.
- High traction outer synthetic rubber stays grippy even when wet or cold.
- Gel absorbs vibration for a smoother feel at the handlebars.
-
Aluminum Rise Style Handlebars Bolt on Replacement for OEM Polaris Handlebars
-
Mountain Grab Bar Mounts Allow for mounting on any 7/8 or 1& 1/8″ Handlebar
-
Accepts 7/8″ and oversize 1 & 1/8″ Handlebars. Universal Installation on any t-post steering post.
-
Replacement LH Side Spring style Scratcher
-
Replacement RH Side Spring style Scratcher
-
Displays Phone inside a weather resistant Handlebar pad
-
Universal Heater kit- requires 12 volt power source.
-
Replacement LH Side Spring style Scratcher
-
Replacement RH Side Spring Style Scratcher
-
STANDARD PLASTIC MOMETARY PUSH BUTTON
-
Bolt on intstallation allowing Rider to position Hook orientation
-
Kit includes Grips and hooks to transform any RSI aluminum Handlebar
-
Steel Reversible Double Coil Wire Scratchers with Storage mounts
-
10″ Universal Throttle Cable Extension
-
Standard Square heater element grip heaters
-
Universl Grip insulator, thin profile, synthetic based insulator install in seconds.
*Required for all machines using grip heaters*
-
Lightweight Wire type Scratcher. Universal installation
-
Easy and effective way to convert your flat plate steering post into a T-post allowing for pivoting style risers
-
Complete A-arm scratcher kit includes the following: 16″ Ice Scratchers , 2 Qty A-Arm Ice Scratcher mounts, (Includes 1 of 185-102, QTY 2 of 185-106)
-
Lightweight Flint fire starter with striker. Fire starter with built in Compass and Emergency whistle.
-
First Aid Kit: Water tight Aluminum Storage container 3.5″ Diameter 4.75″ Length compact lightweight package includes many of the essentials for small to medium lacerations in the backcountry.
-
Compact manual chainsaw perfect for getting you out of the less than ideal situation and back on your way.
-
Portable tool kit allows for trail side repairs. this kit can be stored within the HNG Rear bumper, a jacket pocket or any storage compartment on your machine.
Its lightweight and compact size make it convenient for traveling in the backcountry
-
Allows for easy mounting of any Straightline Performance ice scratcher to the A-arm of your snowmobile. **requires the use of 16″ Ice Scratchers. This is just for the A-arm Mount only.
-
Quickest and easiest Solution for a leaky, and hard to remove oil cap
-
Protects the powdercoat on your rails and keeps ice scratchers in the stored position until they’re ready to be deployed
-
Allows the ice scratcher carbide tip to stored when not in use.
-
Replacement Ice Scratcher tips for your Straightline Performance cable Ice Scratchers
-
Left Hand Replacement Scratcher end
-
Replacement Ice Scratcher end (sold each does not include tip) Right Hand / Right Side of Snowmobile
Right Hand Replacement Scratcher end
-
Universal compressor works on most primary and secondary clutches (does not work on P-Drive Primary clutch or QRS Secondary)
-
Universal Alignment bar, best way to ensure your clutches are aligned. Comes with instructions including off-sets for most modern machines.
-
This Spring puller is a must for every snowmobiler’s tool box. No more struggling to stretch your exhaust springs.
-
Complete adjustable weight kit or Fine Tuning kit
-
simple and easy bolt on kit just add your favorite set of Polaris/ Arctic Cat weights **Does not work on machines equipped with Arctic Cat Team Based Clutches.**
-
2.5lb Nitrous Bottle (non-siphon tube)
