Latest Products
-
UNIVERSAL BILLET ALUMINUM SINGLE ROCKER SWITCH ON/OFF (7/8 MOUNTING) BLACK ANODIZED
$ 39.95
-
Hustler Aluminum 7/8″ CLAMP AREA – 7/8″ HOOKED HANDLEBAR - 13 DEGREE SWEEP – 1″ RISE – 30″ WIDE – 1″ RISE - Hydro Dipped Carbon Fiber
$ 149.95
-
POLARIS 650/850/900R/BOOST TETHER MOUNT FOR RMK STEERING STEM
$ 19.95
-
Ski-Doo QRS Secondary Spring - Torsional Black
$ 25.00
-
ARCTIC CAT CATALYST CHASSIS BILLET ALUMINUM MOMENTARY KILL SWITCH BLACK ANODIZED W/ OEM CONNECTOR
$ 59.95
-
Snowmobile specific grip glue. Will not break down in snowmobile grip heater scenario
-
• One piece 5″ rubber grip.
• Ultra tacky diamond grip surface is soft and comfortable.
• Compatible with hand warmers.
• Sold per pair.
-
• One piece 8″ rubber grip.
• Ultra tacky diamond grip surface is soft and comfortable.
• Compatible with hand warmers.
• Sold per pair.
-
Bolt on intstallation allowing Rider to position Hook orientation
-
Kit includes Grips and hooks to transform any RSI aluminum Handlebar
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
Universal Installation on any machine With Pivoting or Angled Risers (not recommended for Aluminum Rise Style Handlebars that have a crossbar) Machines Equipped With Pivot adaptors should use Large Bar pad
-
- Self adhesive grip tape to fully wrap your handlebars and hooks with a seamless finish.
- High traction outer synthetic rubber stays grippy even when wet or cold.
- Gel absorbs vibration for a smoother feel at the handlebars.
-
Aluminum Rise Style Handlebars Bolt on Replacement for OEM Polaris Handlebars
-
Mountain Grab Bar Mounts Allow for mounting on any 7/8 or 1& 1/8″ Handlebar
-
Accepts 7/8″ and oversize 1 & 1/8″ Handlebars. Universal Installation on any t-post steering post.
-
Replacement LH Side Spring style Scratcher
-
Replacement RH Side Spring style Scratcher
-
Displays Phone inside a weather resistant Handlebar pad
-
Standard 2 Wire Grip heaters OEM terminals plug and play installation
-
Billet Throttle block uses OEM Kill Switch
-
Billet Throttle block With Plug and Play Billet Kill Switch
-
Billet Throttle block With Universal Billet Kill Switch
-
Replacement LH Side Spring style Scratcher
-
STANDARD PLASTIC MOMETARY PUSH BUTTON
-
Bolt on intstallation allowing Rider to position Hook orientation
-
Add handlebar hooks to your favorite handlebars
- single bolt locking design for ease of install
**Sold individually to put hooks on both ends of your handlebars order qty 2**
-
Kit includes Grips and hooks to transform any RSI aluminum Handlebar
-
10″ Universal Throttle Cable Extension
-
Standard Square heater element grip heaters
-
Universl Grip insulator, thin profile, synthetic based insulator install in seconds.
*Required for all machines using grip heaters*
-
Lightweight Wire type Scratcher. Universal installation
-
2008-20 Ski-Doo QRS Jackshaft Alignment Shim Kit Includes 4 Clutch Side Bearing Shims, 3 Bearing retainer Shims, 1 Beveled Gear side Retainer Shim, 3 Gear side Bearing shims
-
Quick adjust, just as the name says not tools required for your trailside clicker changes
-
2009-18 Ski-Doo 600 E-TEC Clutch Kit 0-3000 ft designed to improve Backshift, Acceleration and Top speed
-
The lightest muffler in the industry. Installation is simple and there zero jetting or fuel programming requirements.
-
TRA Primary clutch holder for installation and removal of the TRA primary clutch.
-
Complete A-arm scratcher kit includes the following: 16″ Ice Scratchers , 2 Qty A-Arm Ice Scratcher mounts, (Includes 1 of 185-102, QTY 2 of 185-106)
-
Lightweight Flint fire starter with striker. Fire starter with built in Compass and Emergency whistle.
-
Compact manual chainsaw perfect for getting you out of the less than ideal situation and back on your way.
-
Allows for easy mounting of any Straightline Performance ice scratcher to the A-arm of your snowmobile. **requires the use of 16″ Ice Scratchers. This is just for the A-arm Mount only.
-
Universal installation Reversible ice scratcher, replaceable carbide tip good for years of constand use.
Carbide tip is a wear item and may break do to hitting objects on the trails. This is to protect not having any issues with hanging up on the rail.
12″ Designed to be mounted on the suspension rail
-
Protects the powdercoat on your rails and keeps ice scratchers in the stored position until they’re ready to be deployed
-
Allows the ice scratcher carbide tip to stored when not in use.
-
Replacement Ice Scratcher tips for your Straightline Performance cable Ice Scratchers
-
Replacement Ice Scratcher end (sold each does not include tip) Right Hand / Right Side of Snowmobile
Right Hand Replacement Scratcher end
-
Replacement bit for 151-106
-
Tungsten inserts for TRA Adjustable pin kits
-
Ski-Doo Secondary Spring Fits all RER Clutches HPV, LPV & QRS
-
TRA Heavy Pin Kit 16-27g Includes Tungsten Slugs
-
TRA Light Full Range Pin Kit 11.1-20.3g Includes Tungsten Slugs
-
TRA Light Pin Kit 11.1-16.0g
-
TRA Medium Full Range Pin Kit 13-23.1g Includes Tungsten Slugs
-
SPD31 Ramps Fits all TRA 3, TRA 5 and TRA 7
-
Universal Alignment bar, best way to ensure your clutches are aligned. Comes with instructions including off-sets for most modern machines.
-
This Spring puller is a must for every snowmobiler’s tool box. No more struggling to stretch your exhaust springs.
-
Complete adjustable weight kit or Fine Tuning kit
-
QRS smooth Shift Bearing (works on all 2008 Ski-doo QRS secondary machines) 2012-18 Arcitic Cat Secondary, 2018-21 Arcitc Cat with boss secondary
-
Complete Service Tool kit with everything you need to service your Ski-Doo TRA & QRS secondary clutches. All the tools required to install your own clutch kit.
-
TRA Primary clutch puller for removal of the TRA primary clutch. (works on all TRA’s except 583 and 617 engines)
-
3 Piece Button holder to keep buttons in place for assembly/ disassembly.
